[TRNSYS-users] auto segmentation

Subject: [TRNSYS-users] auto segmentation

From: "elena.bee@libero.it" <elena.bee@libero.it>

Date: Tue, 02 Feb 2016 19:15:43 +0100 (CET)

Authentication-results: spf=fail (sender IP is 144.92.197.244) smtp.mailfrom=libero.it; cae.wisc.edu; dkim=fail (signature did not verify) header.d=libero.it;cae.wisc.edu; dmarc=fail action=quarantine header.from=libero.it;

Dkim-signature: v=1; a=rsa-sha256; c=relaxed/relaxed; d=libero.it; s=s2014; t=1454436943; bh=omzwlCRwdwgXXwPO5+aOh0BupcfF8YmH6tltErocuAc=; h=Date:From:Reply-To:To:Subject; b=XLy/BGo9vXQbGXWUmp+x0BAP54m1vZ+APaFq5pXGQKit/WYXWuwbF6lIszK17bs/T LP4C+7L68E7Lc5YNfWQ6QYHR6mWQhOl94uc7+p3WG6tHX3xT8vEc4WCAWm6RhL4ITE GzqGAJTIhFL4yBC3n1E0WiIa+W8IMHw06bcwQ05ER7KA2ydT0+BqV73Q42THG+4IAT BjT3Rv0r+FN4uxav9dujHF1ev3mhwANtDTizpzRHUPtQZfX2kd5j7P+Y60IySoXLTe +joVSxNIV/mlIc7uCkAjPEqQUVdVhpjswv9Qs6d5bGqImu2sWGrULo+TyNXFiz4GIV 86CS6eaiY7rZQ==

List-archive: <http://lists.onebuilding.org/pipermail/trnsys-users-onebuilding.org/>

List-help: <mailto:trnsys-users-request@lists.onebuilding.org?subject=help>

List-id: "TRNSYS users mailing list at OneBuilding.org" <trnsys-users-onebuilding.org>

List-post: <mailto:trnsys-users@lists.onebuilding.org>

List-subscribe: <http://lists.onebuilding.org/listinfo.cgi/trnsys-users-onebuilding.org>, <mailto:trnsys-users-request@lists.onebuilding.org?subject=subscribe>

List-unsubscribe: <http://lists.onebuilding.org/options.cgi/trnsys-users-onebuilding.org>, <mailto:trnsys-users-request@lists.onebuilding.org?subject=unsubscribe>

Reply-to: "elena.bee@libero.it" <elena.bee@libero.it>, "TRNSYS users mailing list at OneBuilding.org" <trnsys-users@lists.onebuilding.org>

Resent-date: Tue, 2 Feb 2016 10:15:56 -0800 (PST)

Resent-from: trnsys-users@cae.wisc.edu

Resent-message-id: <0O1X00M62MQHDO50@smtpauth3.wiscmail.wisc.edu>

Spamdiagnosticmetadata: d6406dd6963345c3a6a1585a788b04a5

Spamdiagnosticoutput: 1:2

I'm modeling a building with Type56 and active layer and I would need to do auto segmentation in order to avoid errors during the simulations, but I can't see the auto-segmentation button in Trnbuild-active layer specifications. I remember I did that a year ago, using the same version of trnsys, but then the button disappeared.

Someone has had the same problem? How can I solve it?

Thanks in advance,

kind regards

Elena Bee