Sihem,
You might try opening TRNBuild directly
(..\Trnsys17\Building\TRNBuild.exe) and then select "Open" from the
"File" menu and find the *.b17 file used by your project. Simply
resave the *.b17 file with the newer version of TRNBuild, then try
the simulation again.
Kind regards,
David
On 1/30/2014 10:37, TASCA-GUERNOUTI
Sihem - CEREMA/DTerOuest/DVT/BATEN wrote:
Dear TRNSYS-Users,
I got a building
model that was created with the trnsys17-00-0019
release. I simulate
this building with
17-01-0025 release.
I have the following
error message:
"Wrong version of gentrn.dll was used. TYPE 56 expects version
189.000, but TRNBuild used gentrn.dll version 162.000was loaded."
Does someone know how to fix this problem?
Thank you in advance for your answer!
Sihem
Le 16/01/2014 19:08, TASCA-GUERNOUTI Sihem -
CEREMA/DTerOuest/DVT/BATEN a écrit :
Hi,
Thanks for answers. Just to understand the process, I tested
with a simple example:
* 1 zone in the Type 56, I changed the input type for
occupant internal gains to "Input "
* in type 155:
o I read a fictive daily schedule which represents
the number of present per hour (attached file: profil.txt), then
I did a loop: for i=1:24 { trnoutputs(i)=y(i) } (I put "calling
mode = 10")
* In simulation studio I connect the output from Type 155 to
the input for Type 56.
* I print the type 155 outputs (attached file: Type25a.txt).The
file contains 24 values equal to 1 (the first is 0). These
values does not match to the given schedule.
Could you help me to understand this result?
Thanks,
Sihem
PS: As a reminder, I use stochastic models, in matlab to
calculate the annual states of occupants/hour. I need to use
this output as an input in trnsys for occupancy gains
calculation.
Le 10/01/2014 18:20, "> Adam Rysanek (par Internet, dépôt trnsys-users-bounces@cae.wisc.edu)"
a écrit :
Dear Sihem,
I have had the exact same scenario in the past
(stochastic occupancy from Type 155 for simulation in Type
56).
Step 1: In TRNBUILD, for each building zone (or for all
zones), you change the input type for occupant internal
gains from "Constant" or "Schedule" to "Input". This assigns
a new input variable to the Type 56 component in TRNSYS.
Step 2: In Simulation Studio, connect the corresponding
output from Type 155 to the new input you created for Type
56.
Step 3: Repeat for all other required zones.
As I wrote this, I just saw David Bradley's response,
which is helpful.
Regards,
Adam
------
Adam
Rysanek, BASc, MScE, PhD
Research
Associate
Energy
Efficient Cities initiative | EECi
Department of Engineering
Trumpington Street
University of Cambridge
Cambridge CB2 1PZ
United Kingdom
Mobile: +44 750 332 3100
Office: +44 1223 766 968
Hi,
I'm modelling a building using type 56 and the occupancy
schedule with matlab (stochastic model for occupancy).
The occupancy vary through the year for each zone and
each occupant.
I get the
number of occupants
per zone from
TRNSYS to calculate the
probabilities of presence in Type 155.
The yearly occupancy schedule (8760 values) is an output of
Type
155. Is
there any way for including this schedule in Trsnys as
an input?
Thanks for any advice you can give.
Best regards
Sihem
--
_______________________________________________ TRNSYS-users
mailing list TRNSYS-users@cae.wisc.edu
https://mailman.cae.wisc.edu/listinfo/trnsys-users
_______________________________________________
TRNSYS-users mailing list
TRNSYS-users@cae.wisc.edu
https://mailman.cae.wisc.edu/listinfo/trnsys-users
_______________________________________________
TRNSYS-users mailing list
TRNSYS-users@cae.wisc.edu
https://mailman.cae.wisc.edu/listinfo/trnsys-users
--
***************************
David BRADLEY
Principal
Thermal Energy Systems Specialists, LLC
22 North Carroll Street - suite 370
Madison, WI 53703 USA
P:+1.608.274.2577
F:+1.608.278.1475
d.bradley@tess-inc.com
http://www.tess-inc.com
http://www.trnsys.com
|