Re: [TRNSYS-users] error when importing trnsys 3d- model in simulation studio

To: "TRNSYS users mailing list at the Solar Energy Lab, UW-Madison" <trnsys-users@cae.wisc.edu>

Subject: Re: [TRNSYS-users] error when importing trnsys 3d- model in simulation studio

From: Brian Raichle <brian.raichle@gmail.com>

Date: Sun, 24 Mar 2013 21:25:24 -0400

Dkim-signature: v=1; a=rsa-sha256; c=relaxed/relaxed; d=gmail.com; s=20120113; h=mime-version:x-received:in-reply-to:references:date:message-id :subject:from:to:content-type; bh=psQnM8YOs8ZXWuNqxm4jKCqpRb0nQdlCP3ByOssAaYY=; b=DR9FUOW1UzRDoZ+8R9XAkfQ9kio7IjIKmjzJW0hyt7R2gBXIqgVWHgUrySV+KokfST HddV3/vthB4yYtUUoaHzJ+70L45A9GBT+RwGIpCwaYRMXcNC4NP+Hvlt2OkFZJei2wvE BXX2slBGVDOxWPshJ4ZTtS/qMWTtiHGL1H9aKcix4KEhorjUjxIXyUrm9tZDmqv2nGqz 71J4zXZSFpJbEQVtifZmVtf4A/GMBKC4DaLyQ55hYfDqoo1123umPjDUBkfAx0SH+QOj nPb4Goqj7gS2KuvXD4376aLULEkNXpru1yvgS9LEwyDW1TJ+u+zqnp4WvbJx0VDsS1Oh LlbQ==

In-reply-to: <A4B42D1B081BF84D86B0B21984D52FDA3ABDE57D@SRV-MAIL2-ROE.VK.Roeselare.be>

List-archive: <http://mailman.cae.wisc.edu/pipermail/trnsys-users>

List-help: <mailto:trnsys-users-request@cae.wisc.edu?subject=help>

List-id: "TRNSYS users mailing list at the Solar Energy Lab, UW-Madison" <trnsys-users.cae.wisc.edu>

List-post: <mailto:trnsys-users@cae.wisc.edu>

List-subscribe: <https://mailman.cae.wisc.edu/listinfo/trnsys-users>, <mailto:trnsys-users-request@cae.wisc.edu?subject=subscribe>

List-unsubscribe: <https://mailman.cae.wisc.edu/options/trnsys-users>, <mailto:trnsys-users-request@cae.wisc.edu?subject=unsubscribe>

References: <A4B42D1B081BF84D86B0B21984D52FDA3ABDE57D@SRV-MAIL2-ROE.VK.Roeselare.be>

Reply-to: "TRNSYS users mailing list at the Solar Energy Lab, UW-Madison" <trnsys-users@cae.wisc.edu>

On Sun, Mar 24, 2013 at 4:13 PM, Jorn Ostijn <jorn.o@vkgroup.be> wrote:

Hey everyone,

When making a 3D Building project (multizone), I encountered an error when trying to open my .idf-model (google sketchup).
The error is the following:
"At least 2 surfaces are required per zone!"

What 's weird about this error, is that I can not find a zone consisting of less than 2 surfaces + I can't find "surface -1" in my model.

I searched but have not been able to solve this error yet.
Is anyone familiar with this error? Where lies the problem?
You can find my .idf-model in annexe.

Thank you very much for helping me out,

Jorn Ostijn

Project engineer
VK Engineering

SUBSCRIBE TO OUR E-LETTERS click here

****DISCLAIMER****
This communication is confidential and for the sole useof the addressee. If you are not the intended recipient,
please immediately notify the sender by e-mail at the address shown and then delete it from your system
without copying, disclosing or forwarding its contents. Thank you.

_______________________________________________
TRNSYS-users mailing list
TRNSYS-users@cae.wisc.edu
https://mailman.cae.wisc.edu/listinfo/trnsys-users