Dear Mr. Bradley,
Thanks for your reply!
But in the TRNFlow manual: there it is explained that "As soon as TRNFLOW is turned on, (...) in the simulation the defined infiltrations, ventilations and couplings will be replaced with the calculated air flows."
The fact is that I defined initial CO2% as 1000 ppm in the test room in TRNFlow, and I defined the ambient CO2% as 380 ppm. Meanwhile, I defined the infiltration rate as 0.5276 1/h in TRNBUILD. I want to compare the CO2% reducing curve in the test room based on the infiltration rate 0.5276 1/h of actual measurement value with by TRNSYS simulation. But when I used TRNFLOW, the defined infiltration rate as 0.5276 1/h in TRNBUILD was replaced maybe. 1000 ppm in the test room keeps constant. Please explain this! Or tell me how to compare the test room infiltration rate of actual measurement value with by TRNSYS/TRNFlow simulation?
Many thanks!
Br.
wang
Dear Mr. Bradley,Thanks for your reply!But in the TRNFlow manual: there it is explained that "As soon as TRNFLOW is turned on, (...) in the simulation the defined infiltrations, ventilations and couplings will be replaced with the calculated air flows."
The fact is that I defined initial CO2% as 1000 ppm in the test room in TRNFlow, and I defined the ambient CO2% as 380 ppm. Meanwhile, I defined the infiltration rate as 0.5276 1/h in TRNBUILD. I want to compare the CO2% reducing curve in the test room based on the infiltration rate 0.5276 1/h of actual measurement value with by TRNSYS simulation. But when I used TRNFLOW, the defined infiltration rate as 0.5276 1/h in TRNBUILD was replaced maybe. 1000 ppm in the test room keeps constant. Please explain this! Or tell me how to compare the test room infiltration rate of actual measurement value with by TRNSYS/TRNFlow simulation?Many thanks!Br.wang.2011/2/22 David BRADLEY <d.bradley@tess-inc.com>
Wang,
TRNBuild offers an output (NTYPE96) which is the air change rate of infiltration. TRNBuild also offers an output for the energy gain (or loss) from infiltration (NTYPE4)
Regards,
David
On 2/21/2011 15:16, 王洋 wrote:Dear all,
I want to compare the test room infiltration rate of actual measurement with by TRNSYS simulation. Maybe as you know, in the TRNFlow manual: there it is explained that "As soon as TRNFLOW is turned on, (...) in the simulation the defined infiltrations, ventilations and couplings will be replaced with the calculated air flows."
I defined CO2% as 1000 ppm in TRNFlow, then I want to observe CO2%'s reducing curve when infiltration rate is 0.5276 1/h (I measured the value in the test room), so I defined the infiltration rate as 0.5276 1/h in TRNBUILD. But when I used TRNFLOW, the defined infiltration rate as 0.5276 1/h in TRNBUILD was replaced. And 1000 ppm keeps constant.
Please tell me how to get the infiltration rate curve using TRNSYS/TRNFLOW or how to explain this ?
Many thanks!
br
wang
在 2011年2月21日 下午12:07，王洋 <wanghongyang1767@gmail.com>写 道：
Dear all,
I want to compare the test room infiltration rate of actual measurement with by TRNSYS simulation. Maybe as you know, in the TRNFlow manual: there it is explained that "As soon as TRNFLOW is turned on, (...) in the simulation the defined infiltrations, ventilations and couplings will be replaced with the calculated air flows."
I defined CO2% as 1000 ppm in TRNFlow, then I want to observe CO2%'s reducing curve when infiltration rate is 0.5276 1/h (I measured the value in the test room), so I defined the infiltration rate as 0.5276 1/h in TRNBUILD. But when I used TRNFLOW, the defined infiltration rate as 0.5276 1/h in TRNBUILD was replaced. And 1000 ppm keeps constant.
Please tell me how to get the infiltration rate curve using TRNSYS/TRNFLOW or how to explain this ?
Many thanks!
br
wang
2011/2/21 <trnsys-users-request@cae.wisc.edu>
Send TRNSYS-users mailing list submissions to
trnsys-users@cae.wisc.edu
To subscribe or unsubscribe via the World Wide Web, visit
https://mailman.cae.wisc.edu/listinfo/trnsys-users
or, via email, send a message with subject or body 'help' to
trnsys-users-request@cae.wisc.edu
You can reach the person managing the list at
trnsys-users-owner@cae.wisc.edu
When replying, please edit your Subject line so it is more specific
than "Re: Contents of TRNSYS-users digest..."
Today's Topics:
1. Problems with calling EES (Type66a) (Doms Joris)
2. wall definition (davide disco)
---------- 已转发邮件 ----------
From: Doms Joris <joris.doms@vito.be>
To: "trnsys-users@cae.wisc.edu" <trnsys-users@cae.wisc.edu>
Date: Sun, 20 Feb 2011 22:43:08 +0100
Subject: [TRNSYS-users] Problems with calling EES (Type66a)
Dear TRNSYS users,When simulating an applied thermal system, I'm using EES for the hydronic part. I programmed the hydronic circuit in EES and coupled it with TRNSYS via Type 66a. This coupling works fine, but;The problem is that the simulation runs very slow. Every timestep that TRNSYS calls EES, the EES project is opened and closed. Is there a way to set some settings so EES isen't closed and reopened each time, this would minimize the solution time alot.Thanks on advanceJoris Doms
This e-mail, any attachments and the information it contains are confidential and meant only for the use of the addressee(s) only. Access to this e-mail by anyone other than the addressee(s) is unauthorized. If you are not the intended addressee (or responsible for delivery of the message to such person), you may not use, copy, distribute or deliver to anyone this message (or any part of its contents) or take any action in reliance on it. In such case, you should destroy this message and notify the sender immediately. If you have received this e-mail in error, please notify us immediately by e-mail or telephone and delete the e-mail from any computer.
All reasonable precautions have been taken to ensure no viruses are present in this e-mail and its attachments. As our company cannot accept responsibility for any loss or damage arising from the use of this e-mail or attachments we recommend that you subject these to your virus checking procedures prior to use.
---------- 已转发邮件 ----------
From: davide disco <chester_83@hotmail.it>
To: <trnsys-users@cae.wisc.edu>
Date: Mon, 21 Feb 2011 11:57:59 +0100
Subject: [TRNSYS-users] wall definition
Dear all,
when entering data in Trnbuild I have to describe the walls of the zone: if, looking at the plant of the building, the building has more than a wall south oriented for example (wall to the left in the plant) I should enter in Trnbuild each section of wall facing south or I should enter a unique wall that is the sum of all sections of wall facing south?
Thanks in advace.
Best regards
_______________________________________________
TRNSYS-users mailing list
TRNSYS-users@cae.wisc.edu
https://mailman.cae.wisc.edu/listinfo/trnsys-users
_______________________________________________ TRNSYS-users mailing list TRNSYS-users@cae.wisc.edu https://mailman.cae.wisc.edu/listinfo/trnsys-users-- *************************** David BRADLEY Principal Thermal Energy Systems Specialists, LLC 22 North Carroll Street - suite 370 Madison, WI 53703 USA P:+1.608.274.2577 F:+1.608.278.1475 d.bradley@tess-inc.com http://www.tess-inc.com http://www.trnsys.com