[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
Re: [TRNSYS-users] Visual Fortran run-time error
The three slope inputs must be set to the same value. Slope is defined as 0 degrees = horizontal and 90 degrees = vertical facing the provided surface azimuth. Click on the "more" buttons in the proformas, I'm pretty sure that the slope is defined in each of the models but may be wrong.
Jeff
Sent from my iPhone
> On May 24, 2016, at 6:12 AM, Chaminda Ranaweera via TRNSYS-users <trnsys-users@lists.onebuilding.org> wrote:
>
>
> Hello;
>
> Can anybody kindly tell me the meaning of “Array slope”, of Solar PV “Input” of “Type 94-a” Solar PV Panels. I change the “Array slope” parameter and see the output. But, I couldn’t see any significant variation of output of solar PV panels. It has not defined this parameter or sign convention for that on help manual
>
> I am modeling an array f solar PV panels, I use “Collector Array Shading” for that. It also has “Collector Slope” as “Parameter”. Is that same as ““Array slope” parameter of “Type 94-a”, Solar PV panel.
> The “Weather Data Reading and Processing” also has “Slope of surface” and “Azimuth of surface”. But it is also not defined the sign convention for above two parameters in “Help Manuals”.
> How can we define above three parameters? Can anybody tell me?
>
> According to my knowledge, the maximum solar PV gain shall be when it is oriented towards southern, when we stay in northern hemisphere. But I always gets the maximum solar pv output when Slope of Solar PV is “0” degrees, that means when it is horizontal.
>
> Thank You,
>
> Chaminda
>
> On Mon, 23 May 2016 19:19:30 +0200
> Chaminda Ranaweera via TRNSYS-users <trnsys-users@lists.onebuilding.org> wrote:
>> Hi,
>> I also had the same problem earlier, the problem was there was no enough data rows in weather file. I made my weather file with a note pad program. The weather data must be a multiple of 24.
>> Chaminda
>> On Fri, 20 May 2016 23:44:06 +0000
>> Eleftherios Bourdakis via TRNSYS-users <trnsys-users@lists.onebuilding.org> wrote:
>>> Dear TRNSYS users,
>>> When I change the simulation start time from anything different than 0 hr, I get the following error:
>>> forrtl: severe (408): fort: (2): Subscript #1 of the array VALUE_NOW has value 37 which is greater than the upper bound of 36.
>>> Do you know how I can solve this issue? Up to today TRNSYS was working fine and I could start my simulation at any time I wanted.
>>> Thank you in advance for your help.
>>> Best regards,
>>> Eleftherios Bourdakis
>>> PhD Student
>>> International Centre for Indoor Εnvironment and Energy
>>> Technical University of Denmark
>>> [cid:image001.png@01D1B2B3.C9DA92D0]
>>> Department of Civil Engineering
>>> Nils Koppels Allé
>>> Building 402, Office 227
>>> 2800 Kgs. Lyngby, Denmark
>>> Mobile: (+45) 91940297
>>> Tel dir: (+45) 45254017
>>> Email: elefbur@byg.dtu.dk<mailto:elefbur@byg.dtu.dk>
>>> Web: www.byg.dtu.dk<http://www.byg.dtu.dk>
>> _______________________________________________
>> TRNSYS-users mailing list
>> TRNSYS-users@lists.onebuilding.org
>> http://lists.onebuilding.org/listinfo.cgi/trnsys-users-onebuilding.org
>
> _______________________________________________
> TRNSYS-users mailing list
> TRNSYS-users@lists.onebuilding.org
> http://lists.onebuilding.org/listinfo.cgi/trnsys-users-onebuilding.org