[TRNSYS-users] Genopt and trnsys16 problem

I create .bui and .dck that works properly, I change the parameters value with their name in order to create the template files but once I run genopt, it creates the .bui and .dck files changing the parameter name with the right value, it starts running trnsyss but I have a trnsys error message of the kind: "One error was find in the dek. Check the listing file for more information" and then Genopt stops running. I cannot really understand why it appens, also because if i compare both .dck and .bui files that run properly with those generated by Genopt there is no difference at all (just the value of the parameters). I attach below the listing file.

   The Solar Energy Lab at the University of Wisconsin - Madison, USA
Le Centre Scientifique et Technique du Batiment, Sophia Antipolis, France
           Transsolar Energietechnik GmBH, Stuttgart, Germany
        Thermal Energy System Specialists, Madison Wisconsin, USA

Listing file for: "C:\Users\Narghes\Documents\TESI DI DOTTORATO_CARTELLE\CASI STUDIO\cubo\tmp-genopt-run-1\Simulazione_cubo.dck"

*** Notice at time        :         0.000000
    Generated by Unit     : Not applicable or not available
    Generated by Type     : Not applicable or not available
    Message               : The TRNSYS Executable (TRNExe.exe) and main DLL (TRNDll.dll) are located in "C:\Program Files\Trnsys16_1\Exe"

*** Pre-Processing the TRNSYS EQUATIONs and CONSTANTs to check for fatal errors.

*** Pre-Processing of EQUATIONs and CONSTANTs completed with no fatal errors found.

*** Finished evaluating the EQUATIONs and CONSTANTs and ready to begin processing the remainder of the TRNSYS input file.

VERSION        16
*******************************************************************************
*** TRNSYS input file (deck) generated by TrnsysStudio
*** on Tuesday, February 21, 2012 at 15:18
*** from TrnsysStudio project: C:\Users\Narghes\Documents\TESI DI DOTTORATO_CARTELLE\CASI STUDIO\cubo\Simulazione_cubo.tpf
***
*** If you edit this file, use the File/Import TRNSYS Input File function in
*** TrnsysStudio to update the project.
***
*** If you have problems, questions or suggestions please contact your local
*** TRNSYS distributor or mailto:software@cstb.fr
***
*******************************************************************************
*******************************************************************************
*** Units
*******************************************************************************
*******************************************************************************
*** Control cards
*******************************************************************************
* START, STOP and STEP

CONSTANTS   3
     START=0
     STOP=8760
     STEP=1
* User defined CONSTANTS
! Start time End time Time step

SIMULATION 0.0000000000000000E+00 8.7600000000000000E+03 1.0000000000000000E+00
! Integration Convergence

TOLERANCES 1.0000000000000002E-03 1.0000000000000002E-03
! Max iterations Max warnings Trace limit

LIST
! MAP statement
! Solver statement Minimum relaxation factor Maximum relaxation factor

UNIT   5     TYPE 56
*$UNIT_NAME Type56b
*$MODEL .\Loads and Structures\Multi-Zone Building\Without Standard Output Files\Type56b.tmf
*$POSITION 247 210
*$LAYER Main #
*$#
       PARAMETERS   3
! 1 Logical unit for building description file (.bui)
! 2 Star network calculation switch
! 3 Weighting factor for operative temperature
       3.1000000000000000E+01    0.0000000000000000E+00    5.0000000000000000E-01
       INPUTS   21
! Type15-3:Dry bulb temperature -> 1- TAMB
! Type15-3:Humidity ratio -> 2- RELHUMAMB
! Type69b-2:Fictive sky temperature -> 3- TSKY
! Type15-3:Total tilted surface radiation for surface-3 -> 4- IT_NORTH
! Type15-3:Total tilted surface radiation for surface-1 -> 5- IT_SOUTH
! Type15-3:Total tilted surface radiation for surface-2 -> 6- IT_EAST
! Type15-3:Total tilted surface radiation for surface-4 -> 7- IT_WEST
! Type15-3:Total horizontal radiation -> 8- IT_HORIZONTAL
! Type34:Incident receiver radiation -> 9- IT_SOUTHHADED
! Type15-3:Beam radiation for surface-3 -> 10- IB_NORTH
! Type15-3:Beam radiation for surface-1 -> 11- IB_SOUTH
! Type15-3:Beam radiation for surface-2 -> 12- IB_EAST
! Type15-3:Beam radiation for surface-4 -> 13- IB_WEST
! Type15-3:Horizontal beam radiation -> 14- IB_HORIZONTAL
! Type34:Beam radiation on receiver -> 15- IB_SOUTHHADED
! Type15-3:Angle of incidence for surface-3 -> 16- AI_NORTH
! Type15-3:Angle of incidence for surface-1 -> 17- AI_SOUTH
! Type15-3:Angle of incidence for surface-2 -> 18- AI_EAST
! Type15-3:Angle of incidence for surface-4 -> 19- AI_WEST
! Type15-3:Angle of incidence for horizontal -> 20- AI_HORIZONTAL
! Type34:Angle of incidence -> 21- AI_SOUTHHADED
       15,1                      15,6                      17,1                      15,26                     15,24
       15,25                     15,27                     15,18                     14,1                      15,30
       15,28                     15,29                     15,31                     15,19                     14,2
       15,46                     15,44                     15,45                     15,47                     15,23
       14,12
*** INITIAL INPUT VALUES
       0.0000000000000000E+00    0.0000000000000000E+00    0.0000000000000000E+00    0.0000000000000000E+00    0.0000000000000000E+00
       0.0000000000000000E+00    0.0000000000000000E+00    0.0000000000000000E+00    0.0000000000000000E+00    0.0000000000000000E+00
       0.0000000000000000E+00    0.0000000000000000E+00    0.0000000000000000E+00    0.0000000000000000E+00    0.0000000000000000E+00
       0.0000000000000000E+00    0.0000000000000000E+00    0.0000000000000000E+00    0.0000000000000000E+00    0.0000000000000000E+00
       0.0000000000000000E+00
*** External files
ASSIGN cubo.bui   31
*|? Building description file (*.bui) |1000
*------------------------------------------------------------------------------
* Model "Type34" (Type 34)
*

UNIT 14     TYPE 34
*$UNIT_NAME Type34
*$MODEL .\Loads and Structures\Overhang and Wingwall Shading\Type34.tmf
*$POSITION 243 370
*$LAYER Main #
       PARAMETERS 16
! 1 Upstream component mode
! 2 Receiver height
! 3 Receiver width
! 4 Overhang projection
! 5 Overhang gap
! 6 Overhang left extension
! 7 Overhang right extension
! 8 Left wingwall projection
! 9 Left wingwall gap
! 10 Left wingwall top extension
! 11 Left wingwall bottom extension
! 12 Right wingwall projection
! 13 Right wingwall gap
! 14 Right wingwall top extension
! 15 Right wingwall bottom extension
! 16 Receiver azimuth
       0.0000000000000000E+00    1.0000000000000000E+00    0.0000000000000000E+00    1.0000000000000000E+00    0.0000000000000000E+00
       1.5000000000000000E+00    1.2000000000000000E+00    0.0000000000000000E+00    0.0000000000000000E+00    0.0000000000000000E+00
       0.0000000000000000E+00    0.0000000000000000E+00    0.0000000000000000E+00    0.0000000000000000E+00    0.0000000000000000E+00
       0.0000000000000000E+00
       INPUTS    7
! Type15-3:Solar zenith angle ->Solar zenith angle
! Type15-3:Solar azimuth angle ->Solar azimuth angle
! Type15-3:Total horizontal radiation ->Total horizontal radiation
! Type15-3:Horizontal beam radiation ->Horizontal diffuse radiation
! Type15-3:Beam radiation for surface-1 ->Beam radiation on surface
! Type15-3:Ground reflectance ->Ground reflectance
! Type15-3:Angle of incidence for surface-1 ->Incidence angle of direct radiation
       15,16                     15,17                     15,18                     15,19                     15,28
       15,83                     15,44
*** INITIAL INPUT VALUES
       9.0000000000000000E+01    0.0000000000000000E+00    0.0000000000000000E+00    0.0000000000000000E+00    0.0000000000000000E+00
       2.0000000000000001E-01    0.0000000000000000E+00
*------------------------------------------------------------------------------
* Model "Type15-3" (Type 15)
*

UNIT 15     TYPE 15
*$UNIT_NAME Type15-3
*$MODEL .\Weather Data Reading and Processing\Standard Format\Energy+ Weather Files (EPW)\Type15-3.tmf
*$POSITION 355 296
*$LAYER Weather - Data Files #
       PARAMETERS 18
! 1 File Type
! 2 Logical unit
! 3 Tilted Surface Radiation Mode
! 4 Ground reflectance - no snow
! 5 Ground reflectance - snow cover
! 6 Number of surfaces
! 7 Tracking mode-1
! 8 Slope of surface-1
! 9 Azimuth of surface-1
! 10 Tracking mode-2
! 11 Slope of surface-2
! 12 Azimuth of surface-2
! 13 Tracking mode-3
! 14 Slope of surface-3
! 15 Azimuth of surface-3
! 16 Tracking mode-4
! 17 Slope of surface-4
! 18 Azimuth of surface-4
       3.0000000000000000E+00    3.3000000000000000E+01    3.0000000000000000E+00    2.0000000000000001E-01    7.0000000000000007E-01
       4.0000000000000000E+00    1.0000000000000000E+00    9.0000000000000000E+01    0.0000000000000000E+00    1.0000000000000000E+00
       9.0000000000000000E+01   -9.0000000000000000E+01    1.0000000000000000E+00    9.0000000000000000E+01   -1.8000000000000000E+02
       1.0000000000000000E+00    9.0000000000000000E+01    9.0000000000000000E+01
*** External files
ASSIGN ITA_Bergamo-Orio.al.Serio.160760_IGDG.epw   33
*|? Which file contains the Energy+ weather data? |1000
*------------------------------------------------------------------------------
* Model "Type33e-3" (Type 33)
*

UNIT 16     TYPE 33
*$UNIT_NAME Type33e-3
*$MODEL .\Physical Phenomena\Thermodynamic Properties\Psychrometrics\Dry Bulb and Relative Humidity Known\Type33e.tmf
*$POSITION 460 197
*$LAYER Main #
       PARAMETERS   3
! 1 Psychrometrics mode
! 2 Wet bulb mode
! 3 Error mode
       2.0000000000000000E+00    1.0000000000000000E+00    2.0000000000000000E+00
       INPUTS    3
! Type15-3:Dry bulb temperature ->Dry bulb temp.
! Type15-3:Percent relative humidity ->Percent relative humidity
! [unconnected] Pressure
       15,1                      15,7                      CONST
*** INITIAL INPUT VALUES
       2.2000000000000000E+01    6.0000000000000000E+01    1.0000000000000000E+00
*------------------------------------------------------------------------------
* Model "Type69b-2" (Type 69)
*

UNIT 17     TYPE 69
*$UNIT_NAME Type69b-2
*$MODEL .\Physical Phenomena\Sky Temperature\calculate cloudiness factor\Type69b.tmf
*$POSITION 459 391
*$LAYER Main #
       PARAMETERS   2
! 1 mode for cloudiness factor
! 2 height over sea level
       0.0000000000000000E+00    0.0000000000000000E+00
       INPUTS    4
! Type15-3:Dry bulb temperature ->Ambient temperature
! Type33e-3:Dew point temperature. ->Dew point temperature at ambient conditions
! Type15-3:Horizontal beam radiation ->Beam radiation on the horizontal
! Type15-3:Sky diffuse radiation on the horizontal ->Diffuse radiation on the horizontal
       15,1                      16,8                      15,19                     15,20
*** INITIAL INPUT VALUES
       0.0000000000000000E+00    2.0000000000000000E+01    0.0000000000000000E+00    0.0000000000000000E+00
*------------------------------------------------------------------------------
* Model "Type65d" (Type 65)
*

UNIT 19     TYPE 65
*$UNIT_NAME Type65d
*$MODEL .\Output\Online Plotter\Online Plotter Without File\Type65d.tmf
*$POSITION 653 285
*$LAYER Main #
       PARAMETERS 12
! 1 Nb. of left-axis variables
! 2 Nb. of right-axis variables
! 3 Left axis minimum
! 4 Left axis maximum
! 5 Right axis minimum
! 6 Right axis maximum
! 7 Number of plots per simulation
! 8 X-axis gridpoints
! 9 Shut off Online w/o removing
! 10 Logical unit for output file
! 11 Output file units
! 12 Output file delimiter
       1.0000000000000000E+00    2.0000000000000000E+00    0.0000000000000000E+00    3.0000000000000000E+01    0.0000000000000000E+00
       1.0000000000000000E+03    1.0000000000000000E+00    1.2000000000000000E+01    0.0000000000000000E+00   -1.0000000000000000E+00
       0.0000000000000000E+00    0.0000000000000000E+00
       INPUTS    3
! Type56b: 1- TAIR_Z1 ->Left axis variable
! Type56b: 2- QHEAT_Z1 ->Right axis variable-1
! Type56b: 3- QCOOL_Z1 ->Right axis variable-2
       5,1                       5,2                       5,3
*** INITIAL INPUT VALUES
       T_PT                                     Q_HEAT                                   Q_COOL
       LABELS 3
       Temperatures
       Heat transfer rates
       Graph 1
*------------------------------------------------------------------------------
* Model "Type28b" (Type 28)
*

UNIT 21     TYPE 28
*$UNIT_NAME Type28b
*$MODEL .\Output\Simulation Summary\Results to External File\Without Energy Balance\Type28b.tmf
*$POSITION 439 402
*$LAYER Outputs #
       PARAMETERS 22
! 1 Summary interval
! 2 Summary start time
! 3 Summary stop time
! 4 Logical unit for the output file
! 5 Output mode
! 6 Operation code-1
! 7 Operation code-2
! 8 Operation code-3
! 9 Operation code-4
! 10 Operation code-5
! 11 Operation code-6
! 12 Operation code-7
! 13 Operation code-8
! 14 Operation code-9
! 15 Operation code-10
! 16 Operation code-11
! 17 Operation code-12
! 18 Operation code-13
! 19 Operation code-14
! 20 Operation code-15
! 21 Operation code-16
! 22 Operation code-17
      -1.0000000000000000E+00    0.0000000000000000E+00    8.7600000000000000E+03    3.4000000000000000E+01    2.0000000000000000E+00
      -1.1000000000000000E+01   -1.2000000000000000E+01    3.0000000000000000E+00   -1.0000000000000000E+00    3.6000000000000000E+03
       2.0000000000000000E+00   -4.0000000000000000E+00   -1.1000000000000000E+01   -1.0000000000000000E+00    3.6000000000000000E+03
       2.0000000000000000E+00   -4.0000000000000000E+00   -1.2000000000000000E+01   -1.0000000000000000E+00    3.6000000000000000E+03
       2.0000000000000000E+00   -4.0000000000000000E+00
       INPUTS    2
! Type56b: 2- QHEAT_Z1 ->Summary input-1
! Type56b: 3- QCOOL_Z1 ->Summary input-2
       5,2                       5,3
*** INITIAL INPUT VALUES
       0.0000000000000000E+00    0.0000000000000000E+00
       LABELS 3
       Qvent
       Qheat
       Qcool
*** External files
ASSIGN pippo.sum   34
*|? File for the summary results |1000
*------------------------------------------------------------------------------
* EQUATIONS "Parameters"
*

EQUATIONS   2
     windowHeight = 1.0
     overhangProjection = 1.0
*$UNIT_NAME Parameters
*$LAYER Main
*$POSITION 152 114
*------------------------------------------------------------------------------

         TRANSIENT SIMULATION     STARTING AT TIME = 0.0000000000000000E+00
                                  STOPPING AT TIME = 8.7600000000000000E+03
                                          TIMESTEP =         1 /        1
             DIFFERENTIAL EQUATION ERROR TOLERANCE = 1.0000000000000002E-03
                   ALGEBRAIC CONVERGENCE TOLERANCE = 1.0000000000000002E-03

     DIFFERENTIAL EQUATIONS SOLVED BY MODIFIED EULER

*** Notice at time        :         0.000000
    Generated by Unit     : Not applicable or not available
    Generated by Type     : Not applicable or not available
    Message               : The following Types were loaded from TRNDll.dll: Type56, Type34, Type15, Type33, Type69, Type65, Type28

*** Notice at time        :         0.000000
    Generated by Unit     : Not applicable or not available
    Generated by Type     : Not applicable or not available
    Message               : "Type157_demo_release.dll" was found but did not contain any components from the input file.

*** Notice at time        :         0.000000
    Generated by Unit     : Not applicable or not available
    Generated by Type     : Not applicable or not available
    Message               : "Type204_release.dll" was found but did not contain any components from the input file.

*** Notice at time        :         0.000000
    Generated by Unit     : Not applicable or not available
    Generated by Type     : Not applicable or not available
    TRNSYS Message    199 : TRNSYS found at least one user DLL in the UserLib directory. (Note: Only DLL's including Types that are used in the simulation are loaded)
    Reported information : 0 user DLLs were loaded after searching in "C:\Program Files\Trnsys16_1\UserLib\ReleaseDLLs"

*** Notice at time        :         0.000000
    Generated by Unit     :     5
    Generated by Type     :    56
    Message               : TRNFLOW multi zone air flow model integrated

*** Notice at time        :         0.000000
    Generated by Unit     :     5
    Generated by Type     :    56
    Message               : Active layers and internal window calculations integrated

*** Notice at time        :         0.000000
    Generated by Unit     :     5
    Generated by Type     :    56
    Message               : No internal humidity calculations are performed and no condensation warnings are printed. if any of the outputs ntype 9,10,11,26,29,40,41,47,48 or 49 is specified The humidity calculations, using an internal timestep, will be switched on and condensation checks are performed

*** Notice at time        :         0.000000
    Generated by Unit     :     5
    Generated by Type     :    56
    Message               : Star network calculation: only at simulation start

*** Fatal Error at time   :         0.000000
    Generated by Unit     :    15
    Generated by Type     :    15
    Message               : Unable to correctly read from the supplied data file - please check the file and re-run the simulation.

*** Notice at time        :         0.000000
    Generated by Unit     :     5
    Generated by Type     :    56
    Message               : Geometrical distribution factors for direct solar (GEOSURF) in zone   1 equal zero occurred. Direct solar   radiaton is treated as diffuse radiation!

==========================================================================================
TYPE56 TIME REPORT: (for debugging purpose)
------------------------------------------------------------------------------------------
time_report_unit:   6
time_filter:       .8760E+07 [ms]
==========================================================================================
Level0      Level1      Level2      Level3      Level4        Counter DTime[ms] TTime[ms]
==========================================================================================

*********************************************************************************************************
The Following UNIT Numbers, TYPE Numbers, and Logical Units Were Used in the Supplied TRNSYS Input File:
                         5            15                 4
                        14            28                 6
                        15            33                 9
                        16            34                31
                        17            56                33
                        19            65                34
                        21            69                35

*********************************************************************************************************
Total TRNSYS Calculation Time: 1.7500 Seconds