|
Hello Christina,
thank you for the quick reply. Yes you're right, I'm converting the Qsens only from kJ/hr to W. I then enter the values in Excel and divide my total heating load from a zone by the zone-area. I have a problem especially with the zone 15 and zone 16. These
are interior rooms. An elevator and installation shaft (no heating on) is adjacent to these rooms. The elevator and installation shaft do not fall below a temperature of 15 degrees, so it's impossible that the zone 15 and zone 16 needs that much of heating
power I get in the simulation. I even calculated the heat load manually. I don't know why, but I only get for interior zones a heat load that is way to high. There's somewhere a problem, maybe it's an easy problem, but I do not find it. I checked every link
and the .b18-file but I do not find it. I also have to say, it's my first time working with TRNSYS. Perhaps the problem is in some setting I did wrong.. I hope really you could help me. Thank you in advance for your time, effort and help.
Best regards,
Asma
Von: Sohail, Asma <st159047@stud.uni-stuttgart.de>
Gesendet: Mittwoch, 25. November 2020 07:25 An: asma.sohail@hotmail.de <asma.sohail@hotmail.de> Betreff: WG: Heating Type Manager (Heating Load is too high) Von: TRNSYS-usersIm Auftrag vonhotline via TRNSYS-users Gesendet: Mittwoch, 25. November 2020 03:24:44 (UTC-12:00) Internationale Datumsgrenze West An: TRNSYS users mailing list at OneBuilding.org Cc: hotline Betreff: Re: [TRNSYS-users] Heating Type Manager (Heating Load is too high)
Hello Asma,
I had a quick look at your .tpf-File and it seems that you are using the Qsens output from the building, converting these in the Equations "Q_sens" and then plotting them, right? The building outputs come in kJ/hr,
so in the equation you're only converting them to W, not W/m². I didn't check the project in detail though, so i don't know if that accounts for all of the difference.
I hope this helps, let me know if it is a different problem.
Best,
Christina
Von: TRNSYS-users <trnsys-users-bounces@lists.onebuilding.org> im Auftrag von Asma Sohail via TRNSYS-users <trnsys-users@lists.onebuilding.org>
Gesendet: Mittwoch, 25. November 2020 14:15 An: trnsys-users@lists.onebuilding.org <trnsys-users@lists.onebuilding.org> Cc: Asma Sohail <asma.sohail@hotmail.de> Betreff: [TRNSYS-users] Heating Type Manager (Heating Load is too high)
Hello trnsys-users,
this is Asma from the University of Stuttgart. Right now I'm working at my diploma thesis using TRNSYS and a problem occured we were not able to solve yet. I hope that you might have a solution or an idea how to fix it. In TRNBuild I'm using the Heating Type
Manager with unlimited power to heat a room to a certain temperature (20°C). I'm only using convective heat. But something is not working properly with the simulation. I get a heating load that is far too high for certain rooms. Specifically, it is about
interior rooms with a too high heating load. I've already checked all links or sources of error, but haven't found anything that causes an error. My maximum specific heating load should actually be around 40 W / m² (144 kJ / h per m²), but I get around 100
W/m² (360 kJ/h per m²), although the outside temperature does not fall into the minus range. It would be great if you had an idea
how to fix that or if you could identify the problem. Thank you very much in advance!! I
attached the files I used in case you have time to have a look at them.
Thanks and kind regards
Asma
|
Attachment:
floor_layout.png
Description: floor_layout.png
