_______________________________________________Michel,
You should check with your distributor and get the latest version of the TESS Libraries. It looks like you are using an older version.
Jeff
---
Jeff Thornton President - TESS LLC 3 N. Pinckney Street, Suite 202, Madison WI USA 53703 Office: (608) 274-2577 Fax: (608) 278-1475 www.tess-inc.com E-Mail: thornton@tess-inc.comOn 11/09/2018 12:22 pm, Michel Tamarzians via TRNSYS-users wrote:
Jeff,I just checked it again and I don't see any checkbox...I have attached a screenshot of what I see when choosing Hooke-JeevesKindly advise what to do next.Thank you!Kind regards,Michel
Op vr 9 nov. 2018 om 19:07 schreef Jeff Thornton via TRNSYS-users <trnsys-users@lists.onebuilding.org>:_______________________________________________Michel,
The mult-start option is included in the latest version of TRNOPT. Select Hooke Jeeves and then there's a check box on the Hooke-Jeeves parameters page for multi-start.
Jeff
---
Jeff Thornton President - TESS LLC 3 N. Pinckney Street, Suite 202, Madison WI USA 53703 Office: (608) 274-2577 Fax: (608) 278-1475 www.tess-inc.com E-Mail: thornton@tess-inc.comOn 11/09/2018 11:23 am, David BRADLEY via TRNSYS-users wrote:
Michel,
You are correct; not all of the optimization methods available in GenOpt are implemented in TRNOpt. TRNOpt is designed to work with a particular version of GenOpt. TRNOPT v17 is designed to work with the GenOpt version 3.0.3 and it may be that the optimization algorithm that you want to use was not implemented in that particular version of GenOpt. If that is the case then you'll unfortunately not be able to use the TRNOpt interface. You can still link up Trnsys with GenOpt but you'll need to do so without the interface (ie following the directions in GenOpt's documentation).
kind regards,
David
On 11/09/2018 08:10, Michel Tamarzians via TRNSYS-users wrote:Dear all
To optimize my simulation I want to use the embedded GenOpt in TRNSYS (TRNOPT). In the Genopt manual many different algorithms are given, however not all of them are given as an option when running the genopt with a TRNSYS *dck file. For example, the manual speaks of the Hooke-Jeeves method with multiple starting points (Hooke-JeevesMS) but this is not an option in the tabs. Instead the Hooke-Jeeves method with only one starting point can be chosen. Anyone else having the same issue or knows a solution for this?
Many thanks!
Kind regards,
Michel
_______________________________________________ TRNSYS-users mailing list TRNSYS-users@lists.onebuilding.org http://lists.onebuilding.org/listinfo.cgi/trnsys-users-onebuilding.org
-- *************************** David BRADLEY Principal Thermal Energy Systems Specialists, LLC 3 North Pinckney Street - suite 202 Madison, WI 53703 USA P:+1.608.274.2577 F:+1.608.278.1475 d.bradley@tess-inc.com http://www.tess-inc.com http://www.trnsys.com
_______________________________________________ TRNSYS-users mailing list TRNSYS-users@lists.onebuilding.org http://lists.onebuilding.org/listinfo.cgi/trnsys-users-onebuilding.org
TRNSYS-users mailing list
TRNSYS-users@lists.onebuilding.org
http://lists.onebuilding.org/listinfo.cgi/trnsys-users-onebuilding.org
_______________________________________________ TRNSYS-users mailing list TRNSYS-users@lists.onebuilding.org http://lists.onebuilding.org/listinfo.cgi/trnsys-users-onebuilding.org
TRNSYS-users mailing list
TRNSYS-users@lists.onebuilding.org
http://lists.onebuilding.org/listinfo.cgi/trnsys-users-onebuilding.org