Dear TRNSYS users,
I have imported a 3d building project which i developed with
Google Sketchup 8 ,and i would like to show .prn files as
external files after my simulation.
Which type should i use in order to get this kind of type as
an external file ?
Best regards,
Kostas A. Tsogkas
--Forwarded Message Attachment--
From:
ricardo.palomar@hotmail.com
To:
trnsys-users@cae.wisc.edu
Date: Wed, 6 Jun 2012 11:03:25 +0000
Subject: [TRNSYS-users] Type 1716: ROTARY DESICANT
DEHUMIDIFIER
Hello !!!
I´m trying to use the type 1716: ROTARY DESICANT
DEHUMIDIFIER, but I´m having always the same problem, when
I run the simulation the outputs 8 and 12 (Regeneration air relative humidity,
and Condensate flow rate) are "0.00". And the outputs 2
and 3 (Process air outlet humidity ratio, and Process air outlet relative humidity)
are inconsistent.
Exist any problem running this type?
Thanks !!!
--Forwarded Message Attachment--
From:
samir.chehal@ingerop.com
To:
trnsys-users@engr.wisc.edu
Date: Wed, 6 Jun 2012 14:59:41 +0200
Subject: [TRNSYS-users] Problem with Type 501
Dear Users,
I must modelize a
geothermique pump and I must study the temperature rise at
300m depth.
I connect type 501 with a
heat exchanger and I connect this heat exchanger with my
heat pump.
The problem is that there are
not inputs in type 501 to connect with Hot/Cold side
temperature of heat exchanger.
And so I don't know how
obtain the rise of temperature in the ground (at 300m
depth).
Best regards
--Forwarded Message Attachment--
From:
mcdowell@tess-inc.com
To:
trnsys-users@cae.wisc.edu
Date: Wed, 6 Jun 2012 08:07:23 -0500
Subject: Re: [TRNSYS-users] Problem with Type 501
Samir -
Type 501 is a ground temperature profile model and not a
ground heat exchanger model. You will need to switch to an
actual ground heat exchanger model.
In the future please only post your question once to the
message board. There is no need to repeat the same question
over and over.
Regards,
Tim
---
Timothy P. McDowell
Executive Vice President
Thermal Energy System Specialists, LLC
22 N Carroll St, Suite 370
Madison, WI 53703
608-274-2577
On 2012-06-06 07:59, Samir CHEHAL wrote:
Dear
Users,
I
must modelize a geothermique pump and I must study the
temperature rise at 300m depth.
I
connect type 501 with a heat exchanger and I connect this
heat exchanger with my heat pump.
The
problem is that there are not inputs in type 501 to
connect with Hot/Cold side temperature of heat exchanger.
And
so I don't know how obtain the rise of temperature in the
ground (at 300m depth).
Best
regards
--Forwarded Message Attachment--
From:
antoine.gautier@solamen.fr
To:
trnsys-users@cae.wisc.edu
Date: Wed, 6 Jun 2012 15:22:16 +0200
Subject: [TRNSYS-users] Open source version of Type56
Dear users
I cannot find the opensource version of
Type56 in my Trnsys 17 package.
Is it still accessible somewhere?
Thanks
a lot
--
Antoine
Gautier
Solamen
SAS
+33
6 58 24 02 60
antoine.gautier@solamen.fr
--Forwarded Message Attachment--
From:
mattia.rio@mail.polimi.it
To:
trnsys-users@cae.wisc.edu
Date: Wed, 6 Jun 2012 17:11:33 +0200
Subject: [TRNSYS-users] Shading groups
Hi!!! i have a little problem with my imported 3d model from trnsys 3d
plug-in for sketchup.
I have posted a picture that show my 3d model in sketchup; so, as you
can see, all of the triangular surfaces (into red circle), are made in
perforated corten steel, and i need to give a shading coefficient to
their, otherwise the program will do the simulations considering the
shading surfaces opaque; but actually they are not matt.
if someone have any ideas about how I can do.....
----------------------------------------------------------------
This message was sent using IMP, the Internet Messaging Program.