[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
Re: [TRNSYS-users] open a window
Dear All,
I am also interested this issue!
I have some way to do this (bellow), but write if you know other pleas.
Rana,
There is possibility to coupling TRNSYS with CONTAM (type 97) to simulate airflow.
It seems to me that if you model window properly in CONTAM then you can regulate their opening in TRNSYS.
Regards,
Karol
-----Original Message-----
From: Rana Pratap Poddar [mailto:rppoddar@teri.res.in]
Sent: Thursday, April 05, 2012 7:41 AM
To: trnsys-users@cae.wisc.edu
Cc: trnsys-users@cae.wisc.edu; trnsys-users-bounces@cae.wisc.edu
Subject: Re: [TRNSYS-users] TRNSYS-users Digest, Vol 88, Issue 6
Dear All
Kindly let me know, In Trnsys, is there any method to close and open a window . Share some example copy for the same.
--------------------------------------------------------------------------------
Thanks and Regards
Rana Pratap Poddar
Research Associate
The Energy and Resources Institute (TERI) Darbari Seth Block, Lodhi Road IHC Complex, New Delhi-110003
Ph- 24682100/ 45104900 Ext No- 2170
Mobile: 09999007237
Fax- 24682144/45
Email-rppoddar@teri.res.in
website: www. teriin.org
***********************************************************************************************************
Build Green, Build Wise
Visit Sustainable Habitats (http://www.sustainable-buildings.org/)
Case studies, Latest green buildings, Up-to-date news, Useful resources, and much more...
***********************************************************************************************************
|------------>
| From: |
|------------>
>--------------------------------------------------------------------------------------------------------------------------------------------------|
|trnsys-users-request@cae.wisc.edu |
>--------------------------------------------------------------------------------------------------------------------------------------------------|
|------------>
| To: |
|------------>
>--------------------------------------------------------------------------------------------------------------------------------------------------|
|trnsys-users@cae.wisc.edu |
>--------------------------------------------------------------------------------------------------------------------------------------------------|
|------------>
| Date: |
|------------>
>--------------------------------------------------------------------------------------------------------------------------------------------------|
|04/04/2012 10:36 PM |
>--------------------------------------------------------------------------------------------------------------------------------------------------|
|------------>
| Subject: |
|------------>
>--------------------------------------------------------------------------------------------------------------------------------------------------|
|TRNSYS-users Digest, Vol 88, Issue 6 |
>--------------------------------------------------------------------------------------------------------------------------------------------------|
|------------>
| Sent by: |
|------------>
>--------------------------------------------------------------------------------------------------------------------------------------------------|
|trnsys-users-bounces@cae.wisc.edu |
>--------------------------------------------------------------------------------------------------------------------------------------------------|
Send TRNSYS-users mailing list submissions to
trnsys-users@cae.wisc.edu
To subscribe or unsubscribe via the World Wide Web, visit
https://mailman.cae.wisc.edu/listinfo/trnsys-users
or, via email, send a message with subject or body 'help' to
trnsys-users-request@cae.wisc.edu
You can reach the person managing the list at
trnsys-users-owner@cae.wisc.edu
When replying, please edit your Subject line so it is more specific than "Re: Contents of TRNSYS-users digest..."
Today's Topics:
1. Calling Matlab (Ramadas Narayanan)
2. online plotter in CombiSys (Shuai Deng)
----- Message from Ramadas Narayanan <ramadas.n@gmail.com> on Wed, 4 Apr
2012 11:58:44 +0930 -----
To: trnsys-users@cae.wisc.edu
Subject: [TRNSYS-users] Calling
Matlab
Hello Everyone,
I am trying to run a component written in MATLAB in TRNSYS. For that, I added Type 155 calling MATLAB to my project and run my TRNSYS tpf file.
It runs smoothly and gives some out put. In the corresponding m-file ( given under special cards), I inserted my m-file code in the space for 'all iterative calls' and saved the file. When I run the file, it shows an error "The M-file did not properly set ‘mFileErrorCode’ to 0 when it was called".
Can any one explain this? How can I set set ‘mFileErrorCode’ to 0.
Your reply highly appreciated.
Regards
Ramadas
----- Message from Shuai Deng <deng32@purdue.edu> on Tue, 3 Apr 2012
22:38:13 -0400 (EDT) -----
To: trnsys-users@cae.wisc.edu
Subject: [TRNSYS-users] online plotter in
CombiSys
Dear all,
I downloaded Combisys demo and found it is pretty easy to use as an education tool to show the basic operation of solar combi-system.
I even discussed with some students in my lesson about the content of trd file, sth like: how the data transfer between types, and how to add our cities into the demo to extend its function, and how to add some solar collector types they obtained from google to the demo.
To be honest, I can feel they really like this demo.
One of them asked me a question about how to output the results of two online plotters in the system.
Actually, the system, described in combisys.trd demo file, contains:
a. 2 online plotters: unit 41, type 65, output file: Assign ***.ou1
unit 45, type 65, output file: Assign ***.ou2 They are mainly used for showing the operation information of the system.
In the original content of combisys.trd file, they are set "no need to output result file", just used as two "monitors".
b. Unit 51, Type 24, Monthly Integrator + Unit 52, Type 25, Printer they can be considered as two partners, and work together to output file:
Assign ***.out
c. Unit 50 Type 28 Simulation Summary
output file: Assign ***.sum
The thing is
we remove the "*" before the output statement "Assign ***.ou1" and ou2 in the related groups of online plotters, so that the demo can output these two result files.
however, we found no data is in the ou1 and ou2 file, they are blank.
and other output files works.
So, we did some assumption analysis ( actually, it likes a simple brain storm ) about why it happens:
a. no data are calculated out by demo: that is not true, because online plotter works very, both of them. all the performance curves are shown every calculation step.
b. online plotters only show the results, not record the data into output
file:
we thought that is also not true. The script regarding the online plotter is shown below:
*|[OL2|
*
*
Unit 45 Type 65 Online plotter
*
Parameters 10 ! Here shows 10 parameters of type 65, OFF=0 means display
online; LU=-1 , we guess it is means logical unit =-1?
*
*NbLeft NbRight LeftMin LeftMax RightMin RightMax
6 2 0.0 100000000 0.0 100.0
*NbPlots XGridPts OFF LU
1 10 0 -1
*
Inputs 8
*
44,1 44,2 44,5 44,6 44,7 44,4 EFFCOLL
SOLFRAC
ESol EAux EMains EDHW EHouse ELossTank EffCol
SolFrac
*
*
Labels 5
*
kJ %
Energy
Percentage
Integrated
*
Assign ***.ou2 22 ! here we just remove the header sign "*".
*
*|]
c. this online plotter is type 65c, means a online plotter without file:
because "assign" statement has already been contained, so it seems not to be a right answer.
d. the post-processing will erase the data in the ou1 and ou2 files: that is a interesting idea from one student, but we checked the "out" folder, bat and txt file did not support this assumption.
In a summary, we have no idea about why two output files-ou1 and ou2 are blank.
Thus, I send this email to all of you for a help.
Any comments and advise will be helpful to us.
Thanks,
_______________________________________________
TRNSYS-users mailing list
TRNSYS-users@cae.wisc.edu
https://mailman.cae.wisc.edu/listinfo/trnsys-users
------------------------------------------------------------------------------------------------------------
Disclaimer:
The information contained in this e-mail is intended for the person or entity to which it is addressed, and it may contain confidential and/or privileged material. Any review or other use of this mail or taking any action based on it by persons or entities other than the intended recipient is strictly prohibited.
If you receive this e-mail by mistake, please contact the sender, and delete all copies of this mail.This e-mail has been scanned and verified by McAfee SaaS Email Security, formerly MX Logic.