Guangzhao
My apologies for the delay, I am still working on trying
to get the parameters for your PV module generated. While Type194 is
the preferred model, you could use Type94 for the time being.
As for the mode parameter in Type194, you don't need to worry
about it. For a time, we were adding an extra "mode" parameter to
all new Types that we wrote just in case we needed it in the future
so that we wouldn't run into backwards compatibility problems.
Type194 only has one mode.
Lastly, the voltage of your PV array and the voltage of your
battery bank typically need to match each other. A battery charge
controller can handle some differences but the idea is usually that
you want your DC PV array to run at a voltage that is a bit higher
than the battery bank voltage so that it can be used to charge the
batteries without a step-down voltage converter. The number of cells
within a PV module obviously can't be changed. However, the number
of modules that you connect in series and parallel can be. Your PV
array will run at multiples of about 17.5V, which is about normal
for charging a 12V battery system I would think. If you have PVs in
series, you would need to also have batteries in series as well.
Kind regards,
David
On 3/14/2011 08:21, lvguangzhao wrote:
Hello,David,I
urgently want to get your help.
Following are the parameters I
missed.
Temperature coefficient of
short circuit current = 0.0010 [1/k]
Temperature coefficient of open
circuit voltage = -0.0038 [v/k]
It's a mono-silicon based
panel. All of the parameters I sent to you are from
the product manual. The test result of open circuit
voltage also matches that value.
I also want to know which type
I should use, type194 or type194b? The parameters of
Type194b's seem can be changed. But a message "
Only mode 1 has been implemented, mode 2 was
created for future updates" is showed in mode card.
I'm not sure whether it has been implemented now.
I have another question about the capacity of a
battery bank. The capacity of a battery bank will not
vary with the number of cells in series. So if it means
that the cell capacity should vary with the number
of cells in series?
Best regards!
2011-03-13
发件人： David
BRADLEY
发送时间：
2011-03-09 03:24:00
收件人：
lvguangzhao
抄送：
trnsys-users
主题： Re:
[TRNSYS-users] Questions about Type 194 and Type 665
Guangzhao,
I also need to know the temperature coefficient of short
circuit current and the temperature coefficient of open
circuit voltage. Both of these should be listed on the
manufacturer's data sheet. Also, is this a silicon-based panel
or some other material? The reason I ask is that silicon cells
typically run at about 0.5V per cell so 36 in series would
have an open cell voltage more like 18V than 21.5V. Its not
impossible of course.
Kind regards,
David
On 3/8/2011 05:21, lvguangzhao wrote:
Hello,
David, thank you very much for your
reply.Attached are my project.Following are the
parameters that I am trying to enter into the EES.
Number of cells in series within a module = 36
Open circuit voltage at reference conditions = 21.5
V
Short ciecuit current at reference conditions
= 7.55 amp
Max. power voltage at reference conditions = 17.5 V
Max. power current at reference conditions = 6.86
amp
Module area = 0.92m2
I also have tryed to change some parameters in
EXAMPLE.VAR in the folder of Type194 ,but I didn't
know what to correct.
Thank you in advance !
2011-03-08
发件人：
David BRADLEY
发送时间：
2011-03-02 23:04:11
收件人：
lvguangzhao
抄送：
trnsys-users
主题： Re:
[TRNSYS-users] Questions about Type 194 and Type 665
Guangzhao,
Could you please send me an email containing the
parameters that you are entering into the EES plugin for
Type194? I have run into some similar problems in the
past and may be able to help solve this one. It sounds
from what you describe as though the problem is in
launching the plugin, not actually in having the plugin
solve so perhaps you only need to send me the Trnsys
Studio project that causes the error.
Kind regards,
David
On 3/1/2011 00:47, lvguangzhao wrote:
Hello, I have two
questions to ask.
1. I encountered a
problem when I was trying to change the parameters
of Type 194 using EES. A error "Missing user
function or improper format for Call statement"
was showed after I clicked on the icon on the
parameter card. What's wrong with it?
2. A convertible frequency air source heat
pump is needed in my model but I can't find one in
TRNSYS. Is Type 665 Ok?
2011-03-01
_______________________________________________
TRNSYS-users mailing list
TRNSYS-users@cae.wisc.edu
https://mailman.cae.wisc.edu/listinfo/trnsys-users
--
***************************
David BRADLEY
Principal
Thermal Energy Systems Specialists, LLC
22 North Carroll Street - suite 370
Madison, WI 53703 USA
P:+1.608.274.2577
F:+1.608.278.1475
d.bradley@tess-inc.com
http://www.tess-inc.com
http://www.trnsys.com
--
***************************
David BRADLEY
Principal
Thermal Energy Systems Specialists, LLC
22 North Carroll Street - suite 370
Madison, WI 53703 USA
P:+1.608.274.2577
F:+1.608.278.1475
d.bradley@tess-inc.com
http://www.tess-inc.com
http://www.trnsys.com
--
***************************
David BRADLEY
Principal
Thermal Energy Systems Specialists, LLC
22 North Carroll Street - suite 370
Madison, WI 53703 USA
P:+1.608.274.2577
F:+1.608.278.1475
d.bradley@tess-inc.com
http://www.tess-inc.com
http://www.trnsys.com
|