Re: [TRNSYS-users] TYPE534 Parameters, Error

[lucas.lira@scottish-southern.co.uk]

Hi Edward. 

The error probably refers to the parameters
that you access once you open the plug-in. The area where you set the tanks
volume, nodes, etc etc. 
I'm not sure what is the parameter 45
but usually this kind of error happens when you insert in the plug-in values
that make no sense. (for example by defining 10 nodes in the tank but placing
an outlet at node 11, or by creating a too large coil that can't fit in
the nodes you placed it into).

Take a look if everything there seems
reasonable with special attention to the outlets/inlets position and, in
case of HX inside, if their sizes/position make sence.

Hope it helps

Lucas Lira

From:	trnsys-users-request@cae.wisc.edu
To:	trnsys-users@cae.wisc.edu
Date:	25/02/2010 01:17
Subject:	TRNSYS-users Digest, Vol 62, Issue 45

---

Send TRNSYS-users mailing list submissions to
                
trnsys-users@cae.wisc.edu

To subscribe or unsubscribe via the World Wide Web, visit
                
https://www-old.cae.wisc.edu/mailman/listinfo/trnsys-users
or, via email, send a message with subject or body 'help' to
                
trnsys-users-request@cae.wisc.edu

You can reach the person managing the list at
                
trnsys-users-owner@cae.wisc.edu

When replying, please edit your Subject line so it is more specific
than "Re: Contents of TRNSYS-users digest..."
Today's Topics:

   1. Re: TYPE534 Parameters, Error (Edward Halawa)

----- Message from Edward Halawa <Edward.Halawa@unisa.edu.au> on
Thu, 25 Feb 2010 11:25:08 +1030 -----

To:	trnsys users <trnsys-users@engr.wisc.edu>
Subject:	Re: [TRNSYS-users] TYPE534 Parameters, Error

Dear All,
 
I managed to replace TYPE 60 with TYPE
534. However, when I run the project, the error (see the attachment) appears.
As you can see, the  error message refers to PAR(45). But TYPE 534
only has 5 parameters listed in the proforma. (Note: TYPE534 uses plugin
and shows another window which displays all the parameters such as tank
properties, loss etc.)
 
TYPE534 documentation doesn’t help much
on this.
 
I appreciate your help. 
 
regards,
edward
 [attachment "Error.bmp"
deleted by Lucas Lira/Contractor/SSE] _______________________________________________
TRNSYS-users mailing list
TRNSYS-users@cae.wisc.edu
https://www-old.cae.wisc.edu/mailman/listinfo/trnsys-users


**********************************************************************
The information in this e-mail is confidential and may be legally privileged. It may not represent the views of Scottish and Southern Energy Group. It is intended solely for the addressees. Access to this e-mail by anyone else is unauthorised. If you are not the intended recipient, any disclosure, copying, distribution or any action taken or omitted to be taken in reliance on it, is prohibited and may be unlawful. Any unauthorised recipient should advise the sender immediately of the error in transmission. Unless specifically stated otherwise, this email (or any attachments to it) is not an offer capable of acceptance or acceptance of an offer and it does not form part of a binding contractual agreement. Scottish Hydro Electric, Southern Electric, SWALEC, Atlantic Electric and Gas, S+S and SSE Power Distribution are trading names of the Scottish and Southern Energy Group. 
Scottish and Southern Energy plc, Inveralmond House, 200 Dunkeld Road, Perth, Perthshire, PH1 3AQ. Registered in Scotland Number. 117119
**********************************************************************