Re: [TRNSYS-users] Adsorption chiller, Error related to enthalpy

[<Fuqiao.Wang@fulcrumfirst.com>]

the fan-coil component is actually for water -air, if the water inlet temperature less than, say 0 C, then a warning message comes up, you know in TRNSYS total warning message is limit for most users.

I have updated this model and glycol can be used in my updated model. let me know if you need further help.

cheers

 

Dr Fuqiao Wang

Sustainable Consulting Engineer

FULCRUM CONSULTING

London:         Tel: +44 (0)20 7520 1300/1305  

Edinburgh:      Tel: +44 (0)131 226 0220       

Spain:          Tel: +34 98 5195989

mailto:Fuqiao.Wang@fulcrumfirst.com    

www.fulcrumfirst.com    

 

---

From: David Bradley [mailto:bradley@tess-inc.com]
Sent: 10 February 2009 20:49
To: mc03106delos@yahoo.gr
Cc: trnsys-users@cae.wisc.edu
Subject: Re: [TRNSYS-users] Adsorption chiller, Error related to enthalpy

Sotiris,
  It may be that the problem lies inside the code in an internal iteration (in other words not in a place that you can get to without running the simulation through a Fortran compiler. I would start by disconnecting the inputs to the fan coil (set them equal to constant values if you can) and then watch the outputs of whatever component is just upstream to make sure that the air state and water state going in to the fan coil is realistic.
Kind regards,
 David


SOTIRIS KONSTANTELOS wrote:

Dear TRNSYS users,

I'm trying to simulate a solar powered air conditioning system , which uses an adsorption chiller in order to produce chilled water for the fan coils.The problem is that there is no adsorption chiller-component in the simulation studio. So does anyone know how is it possible, if it's possible, to simulate the adsorption chiller using instead the absorption chiller component?Is there any other way?

I have one more question.When i'm trying to run the simulation using of course the absorption chiller, error manager stops simulation and warns me about an error located at the fan coil component.The exact message is <<Attempted to take the log of a negative number.-Enthalpy (H) is less than or equal to zero>>.The problem is that i can't find anywhere an enthalpy parameter, except for the psychrometrics component where there is an enthalpy output.Where should i search? I should mention that the connected components maybe related with this problem are these; weather data-->psychrometrics-->building<--fan coil<--chiller etc.

My regards,
Sotiris

---

Χρησιμοποιείτε Yahoo!
Βαρεθήκατε τα ενοχλητικά μηνύ ματα (spam); Το Yahoo! Mail διαθέτει την καλύτερη δυνατή προστασία κατά των ενοχλητικών μηνυμάτων
http://login.yahoo.com/config/mail?.intl=gr

_______________________________________________
TRNSYS-users mailing list
TRNSYS-users@cae.wisc.edu
https://www-old.cae.wisc.edu/mailman/listinfo/trnsys-users
  

-- 
***********************************************************************
Thermal Energy System Specialists (TESS), LLC 
David BRADLEY                      22 N. Carroll Street - Suite 370 
Partner                            Madison, WI 53703 
                                   USA
P: +1.608.274.2577 
F: +1.608.278.1475
E-mail: bradley@tess-inc.com 
Web Pages:  http://www.tess-inc.com    and      http://www.trnsys.com

***********************************************************************

Fulcrum Consulting is proud to be a Founding Member of the UK Green Building Council. To find out more visit http://www.ukgbc.org

******************* email confidentiality notice *************************

This message is intended for the addressee recipient only. It is private and confidential. If you have received this message in error, please notify the sender immediately and remove it from your system. If you are not the intended recipient you must not use, disclose, distribute, copy, print or rely on this email. Fulcrum First Ltd Incorporated in England and Wales with Registered Number: 03401753. Registered Office: 62-68 Rosebery Avenue, London EC1R 4RR

************* Fulcrum First Ltd trading as Fulcrum Consulting *************